Oldforge Air / Pneumatic Hammer Chisels, Hammers & Cutters, Scrapers, Punches

Slotted Panel Cutter

Muffler and Tailpipe Remover

Designed to separate telescoped tubing without damage to the inner section. This tool has the exclusive Oldforge CURL-CUT.

Tailpipe Cutoff Tool

The sharp concave edge on the thin blade will cut off the tailpipe with ease.

Control Arm Bushing Remover - 6 Inches

Cold Chisel

Sheet Metal Trimmer Air Chisel

Shock Absorber Chisel - 6 Inch

Rivet and Bolt Cutter

Built with the "beef" and edge to cut rivets and bolts in bumpers, grilles, frames and brackets.

Scraper - 8 Inches

Removes gaskets, rust, undercoating, paint, floor tile, plaster and roof coatings
with ease. The blade is offset for hand clearance. Blade width is 1-1/8". Length 8" (20.3 cm). Stock 1/2" (13 mm).

Taper Punch - 6 Inches

Use for peening and crimping bodies, driving rivets and hinge pins. 3/8" Diameter x 6" Long.

Taper Punch - 6-1/2 Inches

The 1/8" diameter point will drive out pins and rivets.

Sharp Point Taper Punch

Straight Punch

Use for peening and crimping bodies, driving rivets and hinge pins. 1/2 inch tip.

Hammer - 3 1/2 Inches

Excellent for hammering operations such as U-joints, ball joint and body forming work. Length 3-1/2".

Tie Rod Sleeve Breaker - 4 Inches

The vibration of this tool against the tie rod assembly will break rust and corrosion to permit easy adjustment. Length 4" (10.2 cm). Stock 1/2" (13 mm).

Tie Rod Separator

The specific opening between tines of 21/32" does the job quickly and properly.

Ball Joint Separator

The opening between tines is 15/16", which will handle ball joints with a minimum of shock to the assembly.

Body Ripper - 6 Inches

Tough as it's name, the body ripper is a favorite with body service technicians. Cuts a clean, short radius, virtually eliminating the added work of edging and welding. This tool has the exclusive Oldforge CURL-CUT. Length 6" (15.2 cm). Stock 1/2" (13 mm).

Double Cut Body Ripper - 6 1/4 Inches

Panel Cutter - 6 Inches

This is a tool designed for both straight and radius cuts on body and door panels. The cut curls away, making the precision you need easier to achieve. This tool has the exclusive Oldforge CURL-CUT Length 6" (15.2 cm). Stock 1/2" (13 mm).

Nut Splitting Tools - 6 Inches

6" nut splitter provides the extra reach needed to work around air conditioner parts. Length 18 inch (45.7 cm). Opening 5/16 inch (7.94 mm).

Nut Splitting Tools - 10 Inches

10 inches nut splitter can be used to remove the top nuts on shock absorbers and V-8 exhaust flanges. Length 10" (25.4 cm). Opening 3/8" (1 cm).

Nut Splitting Tools - 18 Inches

18" nut splitter provides the extra reach needed to work around air conditioner parts. Length 18 inch (45.7 cm). Opening 3/4 inch (13 mm).

Spot Weld Breaker - 6 Inches

The ideal tool for cutting spot welds. It also works very well for cutting molding and rivets. Length 6" (15.2 cm). Stock 1/2" (13 mm).

Radius Cutter - 6 1/4 Inches

This is an exceptional tool because of its ability to cut a tight radius quickly and smoothly. Length 6-1/4" (15.7 cm). Stock 1/2" (13 mm).

Inside Muffler Cutter - 8 1/4 Inches

The convex cutting edge design will cut the motor side off muffler. These jobs are easier and faster when you use the proper tool. Length 8-1/4" (21 cm). Stock 1/2" (13 mm).

Combination Muffler Cutter - 8 Inches

The convex cutting edge design will fit inside the muffler. Length 8" (20.32 cm)

Outside Muffler Cutter - 8 1/4 Inches

The concave cutting edge design will cut exhaust side of muffler. Length 8-1/4" (21 cm). Stock 1/2" (13 mm).

Splitting Tool - 8 1/4 Inches

The bend of the blade allows this tool to slice through bushings, cylinder sleeves and muffler connections with ease. This tool has the exclusive Oldforge CURL-CUT Length 8-1/4" (21 cm). Stock 1/2" (13 mm).

Retainer Spring -Carded

Will fit .401" diameter shank accessories. The retainer spring grips the shank tighter as the hammering force increases, but lets you snap tools in and out easily.

Stud Remover